LED Bezel - with included 3mm Red LED
Bezel Assembly with 3mm Red LED. Required hole size: 0.25". Washer and hex nut included. LED Specifications: Color Red Lens Diam 3 mm Overall Height 5.4 mm Lens Type Diffused Luminous Intensity Min. 3.6 mCd @If (test) 10 mA Wavelngth (Peak) 568 nm V(FM) Max.(V) Forward Voltage 2.7 V @I(F) (test) 10 mA Min Operating Temp -30° Max Operating Temp 80°
Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
Switch - Vibrato LDR, for Fender® Amps
Optocoupler. Vibrato LDR for Fender Amps. Fix the dead LDR-style tremolo on your vintage Fender amps as well as others.
- Non-polarized optical side is indicated by silver dot and slightly longer leads
- Resistive side is indicated only by slightly shorter leads
Screw - #6 x ¾", Pan Head, Stainless Steel
Package of 12Stainless steel pan head Phillips self-tapping screws. #6 X ¾" length. Good for use with #'s 3,4 and 5.
Screw - #6 x ¾", Flat Head, Stainless Steel
Package of 8Stainless steel flat head Phillips self-tapping screws. #6 x 3/4" length. Good for use with P-H266 & P-H267 & P-H1087N.
Screw - #2 x ⅜, Phillips, Oval Head, SMS, Zinc
Package of 25#2 x 3/8", zinc, oval head, phillips, sms screws. Package of 25.
Screw - 1", Phillips, Oval Head, Matching T-Nut
Package of 41" Oval head, Phillips screw with matching t-nut. (package of 4)
Fuse Holder - for Fender®, 3AG-Type
High quality Fender® Style fuse holder replacement for guitar amplifiers.
- Fits ½" chassis hole diameter
- Mounted by Nut
Fuse Block - for 3AB and 3AG fuses, low profile
Open frame fuse holder with patented self-aligning, snap-in terminal clips. A low profile fuse block featuring individual barriers which reinforce the fuse clips while providing greater protection against clip damage and electrical shock. The uniqu design permits self-alignment of clips to fuse cap. This, plus a one-piece clip / terminal assures low contact resistance. Higher current ratings have been attained using spring brass clips.
Screw - 10-32, Phillips, Flat Head, Machine, stainless steel
Package of 5Phillips flathead machine screw, 10-32 stainless steel. Fine thread. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. This style head is used in applications where protrusion of the fastener above the mating surface is unacceptable. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head. Made from austenitic stainless steels. It contains chromium creating an invisible surface film that resists oxidation making the metal corrosion resistant. If the surface layer is damaged, it rebuilds itself in the presence of oxygen.
Screw - 6-32, Phillips, Pan Head, Machine, Zinc
Package of 5Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Screw - M6-1.0 x 30mm, Phillips, Pan Head, Zinc, coarse thread
Package of 5Phillips pan head machine screw, 1 x 30. Designed to go through a pre-tapped hole or nut to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Handle - Hammond, steel construction, 1427C1
Special Order ItemRound steel handle with 4" mounting hole center. 1.3" tall. Hardware included.
Handle - Hammond, square aluminum, M268-4
Special Order ItemGeneral purpose square aluminum handle. 7.6" by 1.6".