Amplifier Parts

Vibrapod Cones

• Double truncated vinyl cone with 7/16 stationary chrome ball (it does not roll).
• 1" tall by 1 5/8" diameter. 25 lbs maximum weight each.
• Designed for use with Vibrapod isolators or by themselves.
• Suitable for CD, DVD, DSS Receivers, DAC's, Pre amps, Amplifiers, Integrateds, Turntables, Speakers

Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane. You will notice an extended, more defined bass, improved imaging and sound stage, greater dynamics and detail, plus sharper video images. VIBRAPOD Isolators and Cones should be placed under flat areas of the component with more at or near the heaviest areas and at the edges.

Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane.

Zinc plated cold rolled steel glide. 0.39" height, two 0.18" diameter mounting holes (#8 screws), 1.59" mounting center distance.

Peavey Grill Kit (for speaker cone and dust cap protection)

• Manufactured from 1.2mm steel
• Matte black powder coated paint finish
• Surrounded with rubber trim insulator to reduce rattle
• Four 90 degree mounting brackets and 1/4-20 hardware included

Fuse holder cap replacement for P-SP2-500 power receptacle.

Genuine Marshall™ top metal vent. 16 7/8" x 2 ¼".

Vintage style using only the finest tolex available.

• Height: 21"
• Width: 27"
• Depth: 12"

Vintage style using only the finest tolex available.

• Height: 18.5"
• Width: 24"
• Depth: 11"

Flat amp handle. Vintage style 100% soft leather. Reddish-brown. Mounts and screws not included (see P-H282A). Center to center measurement is 6-¾".

Long life general replacement lamps for dials, indicators, etc. The #47 bulb is the most common replacement light used today. Used on the vast majority of Fender amps and many others as well.

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.

#8-32 x 3 ¼" chassis strap screw. Single piece.

Rubber tapered feet with a non-threaded screw hole and a steel washer insert. Sold in a package of 4. Perfect feet for amplifier cabinets or amp heads.

Fender® style lamp jewels are used on countless amps from all kinds of manufacturers. Threading: 9/16 - 24. Note: When back-lit, the color of the amp jewels will be affected by the color of the bulb behind it.

Lamp holder. Relampable front panel indicators accept a variety of T-2 and T-3 ¼ miniature bayonet lamps.

• 11/16" chassis hole
• Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs)
• Rating: 125V, 75W
• Threading: 9/16 - 24

Available Jewels Amber P-L117 Blue P-L120 Clear P-L122 Green P-L116 Purple P-L121 Red P-L115 Violet P-L121V White P-L123

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

Stainless steel pan head Phillips self-tapping screws. #6 X ¾" length. Good for use with #'s 3,4 and 5.

Stainless steel flat head Phillips self-tapping screws. #6 x 3/4" length. Good for use with P-H266 & P-H267 & P-H1087N.

#2 x 3/8", zinc, oval head, phillips, sms screws. Package of 25.

1" Oval head, Phillips screw with matching t-nut. (package of 4)

High quality Fender® Style fuse holder replacement for guitar amplifiers.

• Fits ½" chassis hole diameter
• Mounted by Nut

Phillips flathead machine screw, 10-32 stainless steel. Fine thread. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. This style head is used in applications where protrusion of the fastener above the mating surface is unacceptable. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head. Made from austenitic stainless steels. It contains chromium creating an invisible surface film that resists oxidation making the metal corrosion resistant. If the surface layer is damaged, it rebuilds itself in the presence of oxygen.

Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Phillips pan head machine screw, 1 x 30. Designed to go through a pre-tapped hole or nut to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.