Products
No product page found for product accessorie.
Showing search results for accessorie
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.35
Receptacle - IEC C14, for power cord, 3 prong
Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.
$2.15
Cord - Power, 16 AWG, 3 Conductor, Black
Power Cord / cable - (3 conductor) Bare End, 16 AWG
Starting at $6.99
Socket - 8 Pin Octal, Ceramic PC Mount
8-pin ceramic stand-off tube socket commonly used for octal based power, preamp, and rectifier tubes.
- PC mount
- 1” tail diameter
- Available with standard or gold pins
Starting at $2.49
Socket - 8 Pin, 1.14" mounting hole
8-pin plastic tube socket commonly used for octal based power, preamp, and rectifier tubes.
*Uses P-SH12-1-31 or P-SH2-104-2
- 1-1/8” / 1.14” chassis hole required
- Snap-in Mounting
*Uses P-SH12-1-31 or P-SH2-104-2
$2.80
Cable Clamp - Black Nylon, .203” Mounting Hole
Black nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables. See P-HCABLECLAMP-X for white nylon versions of these clamps.
$0.39
Socket - 9 Pin, Ceramic Base with Aluminum Shield
9-pin tube socket commonly used for preamp tubes or EL84 power tubes (without shield)
- Top mount
- 1-15/16” shield height
- 3/4” chassis hole required
- 1-1/8” mounting centers
- Includes shield
$3.30
Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
- Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
- Securely anchors, insulates, and protects cables at panel entry points
$0.59
Covers - for Chassis Holes, Nickel-plated Steel
High quality chassis hole covers for a wide variety of hole sizes. These covers use tapered tabs that easily snap into the hole to securely hold the cover in place. If a more permanent solution is required, the metal tabs can be bent outward after installing to secure the hole cover to the chassis. These nickel plated covers are a great way to modify an existing chassis or cover up mistakes. This list shows some common hole sizes for a variety of parts used on amplifiers, pedals and other equipment.
Starting at $0.95
Switch - Rotary, 1 Pole, 3 Position
High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95
Socket - 8 pin octal, Sleeve Connectors, 1" with Bracket
Ceramic Tube socket used for octal power tubes.
- Chassis hole: 1” to 1-1/4” depending on mounting (Top: 1” to 1-1/16”, Bottom: 1-1/4”)
- Mounting Centers: 1-1/2” with oblong mounting holes
$2.80
Tube Clip - Octal, Sold individually
Vacuum tube base clip. Grips tube base with teeth to securely hold tube in place. For use with octal sockets with 1-½" mounting centers.
$1.99
Grommet - Rubber, for chassis holes
Listed diameter is inside diameter. Sold in packs of 5.
- 3/8" diameter designed for chassis hole with diameter 1/2"
- 1/8" diameter designed for chassis hole with diameter 1/4"
- 3/16" diameter designed for chassis hole with diameter 5/16"
- 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
- 1/4" diameter designed for chassis hole with diameter 7/16"
- 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $1.75
package of 5
Cable Clamp - Nylon, .203” Mounting Hole
Nylon cable clamps perfect for securing cables to cabinet walls. These clamps feature a .203 in. mounting hole. The ⅜ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the power cord. The ¼ in. diameter cable clamp is commonly used on Fender® amplifiers for securing the RCA reverb tank cables. The 5/16 in. version works well with the S-W125X and S-W132X bare end power cables.
$0.33
Socket - Belton, 8 Pin Octal, Micalex, MIP, PC Mount
Belton 8-pin Micalex tube socket commonly used for octal based power, preamp, and rectifier tubes. Applicable for use with all types of electronic equipment using vacuum tubes.
Features:
- Convenient top or bottom, PC mount capabilities
- 1-1/4” chassis hole required
- 1-1/2” mounting centers
Features:
- Paddle saddle mounting
- Phosphorous bronze pin terminal with tin plating
- Glassfiber filled PPS Insulating material
- Easy mount with saddle of extruded screw hole
- Short leads
$3.50
Battery Clip - 9 Volt with Vinyl Tab
Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.
$0.50
Socket - 9 Pin, Miniature, Standoff Ceramic PC Mount
9-pin ceramic PC mount tube socket commonly used for preamp tubes or EL84 power tubes
- Standoff, PC mount
- 0.70” outer diameter
- 3/4” tail diameter
$2.19
Socket - 8 Pin Octal, Saddle Plate, Black, Bottom Mount
Plastic octal tube socket commonly used for power tubes in many amps.
- Chassis hole: 1 ⅛"
- Mounting Centers: 1 ½"
- Bottom mount
$4.20
Socket - Belton, Micalex, 8-Pin Octal, MIP, Flanged Holes
Belton 8-pin Micalex tube socket commonly used for octal based power, preamp, and rectifier tubes. Applicable for use with all types of electronic equipment using vacuum tubes. This version has circular extruded holes.
$3.50
Power Jack - DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
$0.70
Vacuum Tube Retainer - Belton, for EL84s, High Quality
Retainer (Belton). for use with EL84 tubes, mounts to chassis. Steel plate with nickel plating and natural coil spring. Note: these retainers are for specialized socket below chassis mounting. (See mounting drawing below.) The springs are too short for standard sockets mounted level with the chassis surface.
$1.95
Ring for Retainer - rubber, fits EL34 / 5881 and 6L6GC Tubes
Rubber ring for retainer S-H141 fits EL34/5881 and 6L6GC tubes. Outer Diameter: 1.38" Inner Diameter: 1.00" Thickness: 0.16"
$0.67
LED Lens - Fresnel, Polycarbonate, 5mm
Panel mount led lenses made of high quality polycarbonate. These lenses provide a clean semi-flush appearance with a small panel footprint and work well in any project using LED indicators. Features:
For a version that fits 3mm LEDs, see P-L310-X.
Colors Available:
- ¼” mounting hole
- For panel thicknesses of 1/16” to ⅛”
- Fresnel lens
- Low Profile
For a version that fits 3mm LEDs, see P-L310-X.
Starting at $0.59
Fuse - Slow-Blow, 250V, Miniature, GMD-type 5mm x 20mm
Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5
$3.95
package of 5