Stainless steel strip, microscored to an ultrafine file surface. Remove oxide and corrosion on contacts made of platinum, paladium, moybdenum, gold, tungsten, and silver.
Commonly used to remove oxidation from electronic contact surfaces such as switches or connectors, restoring the connection and revitalizing the surface.

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4.5” cutting edge
• Double sided (both sides are the same gauge)
• 10 gauges available
• Sold individually*
• Made In Japan

*See S-T213-SET for a set of all 10 sizes.

Double edge nut files featuring popular guitar gauges specially designed for slotting nuts. Each set of files is specifically designed for guitars of a particular type. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4” cutting edge
• Set of 3 files
• Made In Japan

Solid steel crowning files with dual cutting edges for precision fret crowning. These should be in any luthier’s tool kit!

• Made of solid steel
• Soft rubber coating on the handle
• Double sided (both sides are the same size)
• 4-3/16” cutting surface
• Available in three sizes to cover most fret sizes (small,medium,large)

Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.

• 4-1/2” cutting edge
• Double sided (both sides are the same gauge)
• Set of 10 files
• Made In Japan

Set contains one of each size:

• 0.010"
• 0.013"
• 0.016"
• 0.024"
• 0.028"
• 0.032"
• 0.036"
• 0.042"
• 0.046"
• 0.056"

Hard chrome coated fret files for crowing stainless steel frets. Each file features a coarse and fine file indicated by the arrows pointing up and down. The larger arrows point to the coarse side and the smaller arrows point to the fine side. The horizontal arrows indicate the cutting direction of the file.

• Hard chrome coated
• Single cut files
• Coarse and fine included on each file
• Medium file has a radius of 2mm
• Jumbo file has a radius of 3mm

Made in Japan. File specially designed for fret end work. Used for rounding fret ends and deburring. Size small = 1 mm for small frets. Size medium = 2 mm for medium frets. Size large= 3 mm for large frets.

Set of files for precision work.
Includes:

• flat
• half round
• round
• square
• three square (i.e. triangular)

Diamond fret file with offset shape for more comfortable fret dressing and improved clearance over the guitar body at high frets. Both full length concave filing grooves (for medium and wide fretwire) uniformly coated with micro industrial diamond particle.

File for use in filing the saddle of acoustic guitars. Available in 2mm or 3mm options.

Adhesive backed standoff with M3 threading. The high-strength adhesive tape allows the standoff to be securely mounted, providing an easy option for mounting PCBs in enclosures. These standoffs use a captive metal nut in a strong nylon plastic base for a durable and lightweight solution.

Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.

5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.

Resealable anti-static bags with a zip top. These pink reusable bags are made of polyethylene and are ideal for storing static sensitive electronic parts such as transistors, JFETs, ICs, CMOS, etc. The zip top uses a heavy duty double-track zipper.

Brush-on adhesive ideal for applying tolex. Cleans up with soap and water. No nasty solvents required. Does not stretch or shrink the vinyl. Comes in quarts or gallons. Specifications: Tolex Glue is a non-flammable, Neoprene based, water borne adhesive formulated to bond tolex and vinyl to wood and wood based substrates. Min. use temp: 45°F Freezes at 32°F and lower Shelf Life: 6 Months Directions: Surfaces to be bonded must be clean. Apply a very thin coat to both surfaces. Very porous surfaces may require more than one coat. Second coat should not be applied until first has dried. Allow to 'flash off' for 20-30 minutes. Cloudy areas indicate incomplete drying. This time can be shortened with forced air and/or heat. Position pieces carefully prior to bringing surfaces together as bond is made instantly.

Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:

• Low profile 0.180" standoff height.
• Offset base allows use when holes are close to the PCB edge.

Stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated strips
• 20 x 10 holes (10 strips)
• 3.04” x 1.55”

Stripboard featuring standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• 1oz/ft2 copper weight
• HASL coated strips
• 30 x 15 holes (15 strips)
• 3.04” x 1.55”

Rocket Sockets by Pepers' Pedals allow for the tightening of various nuts for jacks, potentiometers and switches on guitar effects pedals without scratching the enclosure and damaging the graphics or paint as the typical metal tools will do.

Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green