Products
No product page found for product tools.
Showing search results for tools
Showing results for tool. Search instead for tools
Knob - Top Hat, Gold with Silver Cap, Gibson Style
Gold Gibson style top hat knobs with silver caps. Fits fine knurled (24 spline) pot shafts. Top hat knobs can be found on many Gibson SG models.
$2.25
¼" Jack - Switchcraft, Acoustic End Pin, Mono / Stereo, Nickel
High quality acoustic end pin style jacks from Switchcraft. These nickel plated jacks have three conductors, a strain relief clamp, and a threaded shroud for a professional looking wiring job. The special strap nut can be removed to reveal a hex nut that can be used for external tightening of the jack.
$11.95
Wire - Bus, 100 foot Spool, tinned copper
Solid tinned copper bus wire. 105°C temperature rating, 600V.
Starting at $7.95
Screw - phillips, for pickguards / control plates
Pick guard screws, phillips, ovalhead. Great for mounting countersunk pickguards, control plates, etc.
Colors Available:
- 7/16” threaded portion
- Available in Black, Gold, Nickel, and Chrome plating
- Package of 100
Starting at $8.39
package of 100
Switch - Carling, Mini Toggle, SPDT, 3 Position, Solder Lugs, Short Bat
Carling, SPDT mini toggle with short actuator, 3 positions, ¼" mounting hole diameter, 0.354" bushing length.
- 0.354" bushing length
- 3-Position On/Off/On
- ¼" mounting hole diameter
- Single pole/Double throw (SPDT)
- Solder lugs
$4.95
Bridge - Gotoh, GE103B-T, Tune-O-Matic, Studs / Bushings Post
A modern version of the Tune-o-matic style bridge for the solidbody guitar. Pre-notched saddles with an individual saddle intonation screw retained by mini hex nuts for each one. Threaded thumbwheel style studs and bushings and features hard zinc saddles. Hardware included.
Colors Available:
Starting at $24.20
Neck Plate - Strat Style, Standard, Chrome
Strat style 4 bolt neck plate. (Mounting hardware not included). Four ¼” mounting holes. Made in Korea
$7.25
Standoffs - 0.18", plastic with adhesive backing
Low-profile adhesive standoffs with a 0.180" standoff height that securely attaches your PCB to a flat surface. The post inserts into a 0.125” mounting hole and includes a locking tab that secures the PCB when inserted. It can be used with 1/16” or 1/32” thick PCBs. The 0.6 x 0.6” square base is offset to allow the base to be underneath the board when the mounting hole is close to the PCB edge and the offset base provides a large sticking surface while permitting the PCB to be mounted in tight spaces or close to walls. This can be useful when working with small enclosures. High-quality 3M™ brand double-sided tape secures the standoff to a flat surface. These standoffs are available in packs of 8, 24, or 100 pieces Features:
- Low profile 0.180" standoff height.
- Offset base allows use when holes are close to the PCB edge.
¼" Jack - Pure Tone, Stereo, Double-Open Circuit, Long Thread
Pure Tone’s new long threaded three pole (stereo) 1/4" jack provides full contact for improved connections and signal integrity. This jack locks the cable securely into place creating a greater surface area connection to carry more signal for an improved frequency stability. This jack is a great choice for both mono and stereo applications as well as guitars using active electronics.
$9.99
Switch - Carling, Mini Toggle, 3PDT
Carling mini-toggle switch, 3PDT, ideal for stomp boxes, phase switching, coil-tapping, series/parallel pickup switching in guitars.
- 0.354" bushing length
- 1/4" mounting hole diameter
- On-On Three pole/double throw (3PDT)
$4.95
Pickguard Blanks - 12” x 17.5” sheet, 0.095” thickness
Blank pickguard material sheets for cutting custom pickguards, truss rod covers, and back plates. These sheets come in a variety of colors as well as single ply and three ply options. All colors feature a gloss surface.
Color, Plys Available:
Starting at $12.50
Slug - 1215 Steel, 0.187" Diameter, for Humbucker Pickups
Original, made in USA, steel slugs for making humbucker pickups. These premium slugs are made of 1215 steel. These parts are made using the same materials and processes as the most sought after vintage parts.
Colors Available:
$0.45
Bridge - Gotoh, GE1996T, Floyd Rose® licensed
The Gotoh GE1996T is a high end locking tremolo licensed by Floyd Rose. This version of the locking tremolo is a premium option that is great for new installs or upgrading original units. The hardened steel saddles and patented stud lock technology ensure a rock solid performance. Springs, spring claw, and all mounting hardware are included along with two hex wrenches for dialing in adjustments. 40mm block.
Colors Available:
Starting at $104.60
Potentiometer - Fender, dual Audio, concentric solid shaft
Original Fender, Audio potentiometer, concentric, 250kΩ / 500kΩ, solid shaft.
- Mounting hardware not included
- Used for stacked volume controls on American Vintage '62 Jazz Bass® and Acoustasonic Telecaster®, and Nashville Power Telecaster® guitars
- Will not work with push-on style control knobs; set screw mounting knobs only
$7.95
Nut - Bone, Oversized, 56mm x 11mm x 6.35mm
High quality bone nut blank with extra length, width, and height. These blanks leave the shaping, slotting, and polishing to you so you can control your own custom fit and appearance.
- Measures 56 mm x 11 mm x 6.35 mm
- Sold individually
$4.25
Switch - Pickup Selector, Telecaster, 3-Way
Tele style 3 position pickup selector switch. M3.5 x 0.80 mounting hole threading. Switch tip not included.
$5.35
StripBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing
Stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
Colors Available:
- High-quality 1.6mm FR4 glass-epoxy circuit board
- 1oz/ft2 copper weight
- HASL coated strips
- 20 x 10 holes (10 strips)
- 3.04” x 1.55”
$2.99
StripBoard - Single Sided, 3.04” x 1.55”, 0.1” Spacing
Stripboard featuring standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
Colors Available:
- High-quality 1.6mm FR4 glass-epoxy circuit board
- 1oz/ft2 copper weight
- HASL coated strips
- 30 x 15 holes (15 strips)
- 3.04” x 1.55”
$2.95
Cover - Humbucker, 49.2mm, Nickel Silver, USA
Original, made in USA, covers for humbucker pickups. These premium humbucker covers are made of nickel silver and have a 49.2mm spacing.
Colors Available:
Starting at $6.54
Potentiometer - Bourns, Linear, Solid Shaft, Mini
Bourns Mini Audio Taper Guitar pots. Mini Carbon Element, SolidShaft, Solder Lugs.
- 17mm Body Diameter
- ¼ watt
- 300° rotation
- 6mm solid shaft
- ⅜" Bushing Length
- Tolerance: ±20 %
- Maximum Operating Voltage: 150V
$2.25
Switch - Carling, Mini Toggle, DPDT, 2 Position, Solder Lugs, Flatted
Carling mini-toggle switch, DPDT, ideal for phase switching, coil-tapping, series/parallel pickup switching in guitars. This switch features a flattened actuator.
- 0.354" bushing length
- 2 Position On-On
- ¼" mounting hole diameter
- Double pole/Double throw (DPDT)
$6.55
Bushings - Kluson, ¼" bushings, for retrofitting
Adapter bushings to retrofit US 1/4 inch post Kluson tuners in a headstock drilled for modern die cast tuners. Nickel plating. Set of 6. These Kluson® steel replacement - adapter bushings are intended for use in converting a modern 10mm drilled headstock to accept a vintage Kluson stamped steel tuning machines with the original US 1/4 inch string post diameter. Many repair shops use these to convert a vintage instrument back to original peg head specs
Colors Available:
Starting at $6.95
package of 6
Switch - Carling, Mini Toggle, DPDT, 3 Position, Solder Lugs, Flatted
Genuine Carling DPDT 3-position mini toggle switch with solder lugs. These switches feature a flattened actuator.
- 0.354" bushing length
- 3-Position
- ¼" chassis hole diameter
- DPDT ( Double Pole/ Double Throw) switch
- Solder Lugs
Starting at $6.45
Bridge - Gotoh, BS-TC1S, Vintage Tele, Cut-Down Sides, In-Tune Saddles
Gotoh’s Telecaster bridge has the vintage look and mounting layout with a few modern additions: The In-Tune saddles give you the vintage look with unique grooves cast into the saddle to move the contact point of each string for more accurate intonation. Each saddle is reversible and can be used in any position. This gives you a huge advantage over traditional barrel style saddles that were never designed with precision intonation in mind. The brass saddles will give you that bright Tele twang! The stamped steel base plate’s cut down sides give you the unrestricted string access that many modern players prefer.
Colors Available:
Starting at $44.95